Your cart is currently empty!
Shipping class: Free Shipping
Free Shipping
Victron BatteryProtect 12/24V-220A
The Battery Protect disconnects the battery from non essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
BatteryProtect 220A Features:
12/24V Auto Ranging
The BatteryProtect automatically detects system voltageProgramming made easy
The BatteryProtect can be set to engage / disengage at several different voltages. the seven segment display will indicate which setting has been chosen.A special setting for Li-ion batteries
In this mode the BatteryProtect can be controlled by the VE.Bus BMS. Note: the BatteryProtect can also be used as a charge interrupter in between a battery charger and a Li-ion
battery. See connection diagram in the manual.Ultra low current consumption
Uses only 1.5ma when on and when off or due to low voltage shutdown uses only 0.6ma. This is important in case of Li-ion batteries, especially after low voltage shutdownOver voltage protection
To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16V (12V setting) and 32V (24V setting)Ignition proof
The unit doesn’t use relays but MOSFET switches instead, and therefore no sparks.Delayed alarm output
The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay.Delayed load disconnect and delayed reconnect
The load will be disconnected 90 seconds after the alarm has been activated. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage.Product Video – Introduction to the Victron Energy BatteryProtect
Product Video – How to program the BatteryProtect
SKU 3471 Model # BPR000220400 Barcode # 8719076021452 Brand Victron Energy Shipping Weight 0.9770kg Shipping Width 0.150m Shipping Height 0.075m Shipping Length 0.150m Shipping Cubic 0.016875000m3 
Victron Smart BatteryProtect 12/24V-100A
The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set.
Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual).If required, Bluetooth can be disabled.
SKU 3474 Model # BPR110022000 Barcode # 8719076041245 Brand Victron Energy Shipping Weight 0.5350kg Shipping Width 0.200m Shipping Height 0.100m Shipping Length 0.100m Shipping Cubic 0.002000000m3 
Victron Smart BatteryProtect 48V-100A
The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set.
Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual).If required, Bluetooth can be disabled.
SKU 3476 Model # BPR110048000 Barcode # 8719076041252 Brand Victron Energy Shipping Weight 1.3000kg Shipping Width 0.070m Shipping Height 0.190m Shipping Length 0.070m Shipping Cubic 0.093100000m3 
Victron Smart BatteryProtect 12/24V-220A
The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set.
Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual).If required, Bluetooth can be disabled.
SKU 3475 Model # BPR122022000 Barcode # 8719076041269 Brand Victron Energy Shipping Weight 0.9770kg Shipping Width 0.150m Shipping Height 0.075m Shipping Length 0.150m Shipping Cubic 0.016875000m3 
Victron Cyrix-ct 12/24V-120A intelligent battery combiner
SKU 3449R Model # CYR010120011R Barcode # 8719076022145 Brand Victron Energy Shipping Weight 0.1300kg Shipping Width 0.110m Shipping Height 0.160m Shipping Length 0.050m Shipping Cubic 0.008800000m3 
Victron Cyrix-ct 12/24V-120A intelligent battery combiner Retail
SKU 3450 Model # CYR010120011R Barcode # 8719076022145 Brand Victron Energy Shipping Weight 0.1300kg Shipping Width 0.110m Shipping Height 0.160m Shipping Length 0.050m Shipping Cubic 0.008800000m3 
Victron Cyrix-Li-ct 12/24V-120A intelligent Li-ion battery combiner
SKU 3460 Model # CYR010120412 Barcode # 8719076034339 Brand Victron Energy Shipping Weight 0.1350kg Shipping Width 0.075m Shipping Height 0.050m Shipping Length 0.065m Shipping Cubic 0.243750000m3 
Victron SmartShunt 500A/50mV
The Victron SmartShunt is a powerful battery monitor with Bluetooth on board. It can be installed out of sight, behind the scenes – whilst live data from the device is relayed to your mobile phone or tablet via the VictronConnect App for Android or iOS or on your Mac and PC. The SmartShunt is a great alternative for a BMV battery monitor where a separate display isn’t required.
Available in the below models:
IP21 rated: 300A, 500A, 1000A, 2000A
IP65 rated: 300A (Coming soon), 500A, 1000A, 2000A
Monitored Battery Parameters include:- Battery State-of-Charge (SoC)
- Voltage of up to 2 batteries
- Current Load
- Time to go
- Extensive historical information
- … and much more
Auxilary Input Options:
The SmartShunt can do more than comprehensively monitor your main battery bank – additionally you can choose to either:
- Monitor the voltage of a second battery, for exmaple the starter battery or;
- Connect a temperature sensor (optional accessory) for temperature compensated charging or;
- Monitor the midpoint voltage of your battery bank (cable included) to keep an eye on battery health.
Connection to any Victron GX Device
The SmartShunt also features a VE.Direct port so can also be connected to any device in the GX range including the Colour Controller and Cerbo GX via a VE.Direct cable.
Differences compared to BMV-712 Battery Monitor
- No programmable visual and audible alarm
- No programmable relay.
Smartshunt Video Overview
How to set up a Victron BMV/SmartShunt Battery Monitor for lead and lithium batteries
SmartShunt 300 A / 500 A / 1000 A / 2000 A Supply voltage range 6,5 – 70 VDC Current draw < 1mA Input voltage range, auxiliary battery 6,5 – 70 VDC Battery capacity (Ah) 1 – 9999 Ah Operating temperature range -40 +50°C (-40 – 120°F) Measures voltage of second battery, or temperature, or midpoint Yes Temperature measurement range -20 +50°C VE.Direct communication port Yes RESOLUTION & ACCURACY Current ± 0,1A Voltage ± 0,01V Amp hours ± 0,1 Ah State of charge (0 – 100%) ± 0,1% Time to go ± 1 min Temperature (0 – 50°C or 30 – 120°F) ± 1°C/°F Accuracy of current measurement ± 0,4% Offset Less than 10 / 10 / 20 / 40 mA Accuracy of voltage measurement ± 0,3% INSTALLATION & DIMENSIONS Dimensions (h x w x d) 300 A: 44 x 120 x 44 mm
500 A: 46 x 120 x 54 mm
1000 A: 68 x 168 x 75 mm
2000 A: 68 x 168 x 100 mmShunt connection bolts 300 A: M8
500 A, 1000 A, 2000 A: M10 (0.3937 inch)Protection category IP21 STANDARDS Safety EN 60335-1 Emission / Immunity EN-IEC 61000-6-1 EN-IEC 61000-6-2 EN-IEC 61000-6-3 Automotive EN 50498 Cables (attached) Two 1.5 m cables with 1 A fuse, for ‘+’ connection and starter battery or midpoint connectionAnd a 1.5 m cable with a VE.Direct socket. Note that a (not included) VE.Direct cable is needed to connect a GX device. Temperature sensor Optional (ASS000100000) A note regarding the range of the Bluetooth signal The shunt and the electric cables do negatively influence the range of the Bluetooth signal. The resulting range of 10-15 meter is however satisfactory in most cases. The proximity of other electrically conducting elements, such as the metal chassis of a vehicle or seawater around the hull if a boat, may reduce the range of the Bluetooth signal to an unacceptable level. The solution in such a case is to add a VE.Direct Bluetooth Dongle (ASS030536011) to the system, and to switch off Bluetooth in the SmartShunt.
STORED TRENDS Data stored Battery voltage, Current, State of Charge % as well as the Aux input (Battery temperature, or midpoint deviation, or starter battery voltage). Number of days trends data is stored 46 SKU 3477 Model # SHU050150050 Barcode # 8719076044253 Brand Victron Energy Shipping Weight 0.3740kg Shipping Width 0.135m Shipping Height 0.075m Shipping Length 0.085m Shipping Cubic 0.001400000m3 Unit Of Measure ea 
Victron SmartShunt 1000A/50mV
The Victron SmartShunt is a powerful battery monitor with Bluetooth on board. It can be installed out of sight, behind the scenes – whilst live data from the device is relayed to your mobile phone or tablet via the VictronConnect App for Android or iOS or on your Mac and PC. The SmartShunt is a great alternative for a BMV battery monitor where a separate display isn’t required.
Available in the below models:
IP21 rated: 300A, 500A, 1000A, 2000A
IP65 rated: 300A (Coming soon), 500A, 1000A, 2000AMonitored Battery Parameters include:- Battery State-of-Charge (SoC)
- Voltage of up to 2 batteries
- Current Load
- Time to go
- Extensive historical information
- … and much more
Auxilary Input Options:
The SmartShunt can do more than comprehensively monitor your main battery bank – additionally you can choose to either:
- Monitor the voltage of a second battery, for exmaple the starter battery or;
- Connect a temperature sensor (optional accessory) for temperature compensated charging or;
- Monitor the midpoint voltage of your battery bank (cable included) to keep an eye on battery health.
Connection to any Victron GX Device
The SmartShunt also features a VE.Direct port so can also be connected to any device in the GX range including the Colour Controller and Cerbo GX via a VE.Direct cable.
Differences compared to BMV-712 Battery Monitor
- No programmable visual and audible alarm
- No programmable relay.
Smartshunt Video Overview
How to set up a Victron BMV/SmartShunt Battery Monitor for lead and lithium batteries
SmartShunt 300 A / 500 A / 1000 A / 2000 A Supply voltage range 6,5 – 70 VDC Current draw < 1mA Input voltage range, auxiliary battery 6,5 – 70 VDC Battery capacity (Ah) 1 – 9999 Ah Operating temperature range -40 +50°C (-40 – 120°F) Measures voltage of second battery, or temperature, or midpoint Yes Temperature measurement range -20 +50°C VE.Direct communication port Yes RESOLUTION & ACCURACY Current ± 0,1A Voltage ± 0,01V Amp hours ± 0,1 Ah State of charge (0 – 100%) ± 0,1% Time to go ± 1 min Temperature (0 – 50°C or 30 – 120°F) ± 1°C/°F Accuracy of current measurement ± 0,4% Offset Less than 10 / 10 / 20 / 40 mA Accuracy of voltage measurement ± 0,3% INSTALLATION & DIMENSIONS Dimensions (h x w x d) 300 A: 44 x 120 x 44 mm
500 A: 46 x 120 x 54 mm
1000 A: 68 x 168 x 75 mm
2000 A: 68 x 168 x 100 mmShunt connection bolts 300 A: M8
500 A, 1000 A, 2000 A: M10 (0.3937 inch)Protection category IP21 STANDARDS Safety EN 60335-1 Emission / Immunity EN-IEC 61000-6-1 EN-IEC 61000-6-2 EN-IEC 61000-6-3 Automotive EN 50498 Cables (attached) Two 1.5 m cables with 1 A fuse, for ‘+’ connection and starter battery or midpoint connectionAnd a 1.5 m cable with a VE.Direct socket. Note that a (not included) VE.Direct cable is needed to connect a GX device. Temperature sensor Optional (ASS000100000) A note regarding the range of the Bluetooth signal The shunt and the electric cables do negatively influence the range of the Bluetooth signal. The resulting range of 10-15 meter is however satisfactory in most cases. The proximity of other electrically conducting elements, such as the metal chassis of a vehicle or seawater around the hull if a boat, may reduce the range of the Bluetooth signal to an unacceptable level. The solution in such a case is to add a VE.Direct Bluetooth Dongle (ASS030536011) to the system, and to switch off Bluetooth in the SmartShunt.
STORED TRENDS Data stored Battery voltage, Current, State of Charge % as well as the Aux input (Battery temperature, or midpoint deviation, or starter battery voltage). Number of days trends data is stored 46 SKU 3478 Model # SHU050210050 Barcode # 8719076044260 Brand Victron Energy Shipping Weight 1.0100kg Shipping Width 0.180m Shipping Height 0.080m Shipping Length 0.080m Shipping Cubic 0.115200000m3 Unit Of Measure ea 
Victron Shunt 1000A/50mV-0,5 / 2xM10
SKU 3804 Model # SHU102050200 Barcode # 8719076026198 Brand Victron Energy Shipping Weight 1.1000kg Shipping Width 0.180m Shipping Height 0.060m Shipping Length 0.110m Shipping Cubic 0.011880000m3
