Shipping class: Free Shipping

The Sun Inverter combines a sinewave inverter and a PWM solar charger in one enclosure and is easy to install, with a minimum of wiring.

The inverter allows you to power domestic equipment – requiring 230V AC – using ‘leisure’ or ‘automotive’ batteries rated at 12V.

The solar charger ensures that the batteries are being charged by energy harvested from your solar panels. The charge algorithm is programmable.

The inverter and solar charger parameters can be read out via Bluetooth using the VictronConnect app. In addition to this, the inverter has a VE.Direct Port for connection to a GX device or GlobalLink 520 for system monitoring.

Proven reliability

The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature.

High start-up power

Needed to start loads such as power converters for LED lamps, halogen lamps, or electric tools.

ECO mode

When in ECO mode, the inverter will switch to standby when the load decreases below a pre-set value (min load: 15W). Once in standby, the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a pre-set level, the inverter will remain on.

PWM solar charger

The solar charger ensures that the batteries are charged by energy harvested from your solar panels. The charge algorithm is programmable.

Bluetooth Enabled

The inverter and solar charger parameters can be read and monitored via Bluetooth using the VictronConnect app.

VE.Direct communication port

The VE.Direct Port can be used for connection to a GX device or GlobalLink 520 for system monitoring.

DC and PV connections with screw terminals

No special cable terminals or tools are needed for installation.

 

SUN INVERTER	12/250
Cont. power at 25°C (1)	250VA
Cont. power at 25°C / 40°C	200W / 175W
Peak power	400W
AC output voltage / frequency (adjustable)	230Vac +/- 3% 50Hz or 60Hz +/- 0.1%
DC input voltage range	9.2 – 17V
DC low shut down (adjustable)	9.3V
Dynamic (load dependent) DC low shut down	Configurable via the “dynamic cut-off” setting
DC low restart and alarm (adjustable)	10.9V
Battery charged detect (adjustable)	14.0V
Max. efficiency	87%
Zero-load power	4.2W
Default zero-load power in ECO mode (2)	0.8W
Solar charger technology	Pulse Width Modulation (PWM)
Maximum PV voltage current and power	25V / 15A / 375W
Solar panel type	36 cell solar panel
Charge voltages	Adjustable and able to be temperature compensated (3)
Protections (4)	a – f
Operating temperature range	-40 to +65°C (fan assisted cooling) / Output power deration: 1.25% per °C above 40°C
Humidity (non-condensing)	max 95%
Bluetooth wireless communication	For remote monitoring and configuration
VE.Direct communication port	For remote monitoring and system integration
ENCLOSURE
Material & Colour	Steel chassis and plastic cover (blue RAL 5012)
Battery-connection	Screw terminals
Maximum cable cross-section	10mm² / AWG8
Standard AC outlet	IEC-320 (male plug included)
Protection category	IP 21
Weight	2.4kg / 5.3lbs
Dimensions (h x w x d)	86 x 165 x 260 mm / 3.4 x 6.5 x 10.2 inch
ACCESSORIES
Remote on-off	Yes
Automatic transfer switch	Filax
STANDARDS
Safety	EN-IEC 60335-1 / EN-IEC 62109-1
EMC	EN 55014-1 / EN 55014-2 / IEC 61000-6-1 / IEC 61000-6-3
Automotive Directive	ECE R10-4 EN 50498
(1) Nonlinear load, crest factor 3:1 (2) The default ECO mode retry interval is 2.5 s. The retry interval, stop power level, and start power level are adjustable. (3) Temperature compensation via an optional ”Temperature sensor Quattro, MultiPlus and GX Device” or the “Smart Battery Sense”.	(4) Protection key: a) output short circuit b) overload c) battery voltage too high d) battery voltage too low e) temperature too high f) DC ripple too high

SKU	3165
Model #	SIN121251100
Barcode #	8719076053699
Brand	Victron Energy
Shipping Weight	3.0000kg
Shipping Width	0.160m
Shipping Height	0.220m
Shipping Length	0.310m
Shipping Cubic	0.010912000m3
Unit Of Measure	ea

The MultiPlus is an inverter and charger combination supporting easy installation by way of the Victron MK3-USB interface cable, including the following features: 

• True sine wave inverter
• Adaptive charging
• Hybrid PowerAssist
• PowerControl
• Multiple system integration

The PowerAssist feature will enable the unit to supplement the alternative source. The unit will compensate supply from the battery at times of insufficient power and when no longer required, the excess power will be used for charging. It is therefore no longer necessary to size a generator on the maximum peak load. Use the most efficient size generator instead.

Should there be a grid failure the UPS capability of the inverter is automatically activated. With some units having the ability to enable 6 Multis operating in parallel there is potentially close to uninterrupted and unlimited power.

If three phase power is required, then multiple units can be connected in parallel and configured with the combinations delivering up to 75KW/90 kVA inverter and more than 2000 Amps charging capacity.

Configuring parallel and three-phase systems is made simple with the MultiPlus or the Quattro range both of which bring the possibility of unlimited power with the Multiple system integration functionality.

For detailed information on this product, click on the links to the right.

View additional information on system designs and upgrades.

Boat and Yacht Electrical System Upgrade

Caravan Electrical System Design

 

 

The basics of using VE Configure

MulitPlus 500VA – 1600VA specifications

SKU	3214
Model #	PMP241800000
Barcode #	8719076038238
Brand	Victron Energy
Shipping Weight	7.5000kg
Shipping Width	0.380m
Shipping Height	0.190m
Shipping Length	0.290m
Shipping Cubic	0.020938000m3